ISOFIX Car Seat Malaysia | 360 & i-Size Seats Skip to content

Car seat · ISOFIX

ISOFIX Car Seats in Malaysia

An ISOFIX car seat clicks onto two metal anchor points that are built into your car. You do not thread the seat belt through the seat, so there is less to get wrong when you install it.

Every seat on this page installs with ISOFIX. Prices below are today's prices.

Compare at a glance

Model Why choose it Price
SpinGuard 360 ISOFIX and support leg. ECE R129/04. 40 cm to 150 cm. One-hand 360° rotation. RM939
i-Smart 360 ISOFIX and top tether. ECE R129/03. The lowest-priced Quinton i-Size seat to 150 cm. RM799
Maple 360 ISOFIX and support leg. ECE R129/03. Birth to 12 years. RM1,999
OneSpin+ 360 ISOFIX and support leg, or the seat belt for a car without ISOFIX. ECE R44/04. Birth to 36 kg. RM879
Wowo 360 i-Size ECE R129/04. Newborn to about 150 cm. Built-in chest clip. RM1,649
Wowo S 360° Sits on the Wowo ISOFIX Base. Newborn to 150 cm. RM1,124

Prices are today's prices on this site. Free shipping in West Malaysia.

What is ISOFIX?

ISOFIX is a standard way to fix a child seat to a car. The car has two metal anchor points where the back of the seat meets the seat cushion. The child seat has two arms that click onto them.

ISOFIX is not a safety standard. The safety standards are ECE R129 (i-Size) and ECE R44. Read i-Size car seats and R129 vs R44 in Malaysia.

Does my car have ISOFIX?

Look at the back seat. Cars with ISOFIX usually have a small ISOFIX label or tag where the seat back meets the cushion. Push your fingers into the gap and you can feel the two metal bars. Your car's manual also lists the ISOFIX positions.

If your car has no ISOFIX points, the OneSpin+ 360 also installs with the car's seat belt. See our fitting guide for the Perodua Myvi, Axia and Bezza.

Support leg or top tether?

ISOFIX holds the base of the seat. A third point stops the seat tipping forward in a crash. A support leg stands on the car floor. A top tether clips to an anchor behind the back seat.

The SpinGuard 360, Maple 360 and OneSpin+ 360 use a support leg. The i-Smart 360 uses a top tether, so check that your car has the anchor point.

How to install an ISOFIX car seat

Pull out the two ISOFIX arms. Push them onto the car's anchor points until both click. Then set the support leg on the floor, or clip and tighten the top tether. Try to move the seat: it must not shift.

Read the full steps in how to install an ISOFIX car seat.

Questions parents ask

What is an ISOFIX car seat?

A child car seat that clicks onto two metal anchor points built into the car, instead of being held by the car's seat belt.

How do I know if my car has ISOFIX?

Look for an ISOFIX label where the back seat meets the seat cushion, feel for two metal bars in that gap, or check your car's manual.

Can I use a car seat without ISOFIX?

Yes, if the seat is approved for seat belt installation. The OneSpin+ 360 installs with ISOFIX and a support leg, or with the car's seat belt.

Is ISOFIX the same as i-Size?

No. ISOFIX is the way the seat fixes to the car. i-Size is a safety standard (ECE R129). i-Size seats fit with ISOFIX.

Are Quinton ISOFIX car seats JPJ approved?

Yes. Every Quinton car seat sold in Malaysia is JPJ type approved and carries the E1 E-mark.